29
Brand New Lagun Precision High Speed Gear Head Lathe (Colchester Type) with Clutch Headstock 15″ x 50″ Brand New Lagun Precision High Speed Gear Head Lathe (Colchester Type) with Clutch Headstock, Mdl. AT-1550-G-TW, Colchester Type Engine Lathe, Chip and Coolant Tray, Foot Brake, Full Length Rear Splash Guard, Compound Protection Guard (without limit switch), Manual Indexing Square 4 Position Tool Post, Back Plate, 2 MT4 Centers & Main Spindle Reduction Sleeve, Matrix Disk Clutch, Lead Screw Protection Cover, Halogen Work Light, Operator Protection Guard Compound Mounted, Coolant System, Threading Dial, Leveling Bolts & Pads, Tailstock Quill with Tang, Inch/Metric Dials on Compound & Cross Slide (Direct Readings), Tool Box, Operation Manual, #SMAT1550GTW
Colchester Type Lathe, LAGUN, PRECISIONTags: #SMAT1550GTW, 2 MT4 Centers & Main Spindle Reduction Sleeve, Back Plate, Brand New Lagun Precision High Speed Gear Head Lathe (Colchester Type) with Clutch Headstock 15" x 50" Brand New Lagun Precision High Speed Gear Head Lathe (Colchester Type) with Clutch Headstock, Chip and Coolant Tray, Colchester Type Engine Lathe, Compound Protection Guard (without limit switch), Coolant System, Foot Brake, Full Length Rear Splash Guard, Halogen Work Light, Inch/Metric Dials on Compound & Cross Slide (Direct Readings), Lead Screw Protection Cover, Leveling Bolts & Pads, Manual Indexing Square 4 Position Tool Post, Matrix Disk Clutch, Mdl. AT-1550-G-TW, Operation Manual, Operator Protection Guard Compound Mounted, Tailstock Quill with Tang, Threading Dial, Tool BoxNo brands
Overall Capacity | 15-1/4″ x 50″ |
---|---|
Capacity | . |
Center Height | 7-1/2″ |
Swing Over Bed | 15-1/4″ |
Swing Over Cross Slide | 9-3/8″ |
Distance Between Centers | 50″ |
Headstock | . |
Spindle Nose | D1 – 6 |
Spindle Bore (Max Bar Dia) | 2-3/16″ |
Spindle Speed | 16 Steps |
Spindle Speed Range | 25 to 2000 rpm |
Ranges | 25-33-45-60-80-108-140-190-265-350-470-625-840-1120-1500-2000 |
Carriage | . |
Length of Bed | 19″ |
Width of Bridge | 17-1/2″ |
Cross Slide Travel | 9-1/4″ |
Top Slide Travel | 4-3/4″ |
Bed | . |
Number of V Ways | 3 each |
Bed Width | 11″ |
Swing in Gap | 24″ |
Gap Bed Length Face Plate | 7-5/8″ |
TAILSTOCK | . |
Quill Diameter | 2.8″ |
Quill Center | MT 4 |
Quill Travel | 6-1/8″ |
Feeds and Threads | . |
Range of Whitworth Threads & Number | 2 – 72 TPI / 45 |
Range of Metric Threads & Number | 0.2 – 14 / 39 |
Range of D.P. & Number | 8 – 44 / 21 |
Range of M.P. & Number | 0.3 – 3.5 / 18 |
Longitudinal Feed | 0.0015 – 0.04″ |
Cross Feeds | 0.00075 – 0.02″ |
Coolant Pump Motor | 1/8 HP |
Horsepower | 7.5 HP |
Voltage | 220/440V ~ 3 Phase |
Dimensions (L x W x H) | 102″ x 43″ x 60″ |
Weight | 3740 lbs |
Colchester Type Engine Lathe |
Chip and Coolant Tray |
Foot Brake |
Full Length Rear Splash Guard |
Compound Protection Guard (without limit switch) |
Manual Indexing Square 4 Position Tool Post |
Back Plate |
2 MT4 Centers & Main Spindle Reduction Sleeve |
Matrix Disk Clutch |
Lead Screw Protection Cover |
Halogen Work Light |
Operator Protection Guard Compound Mounted |
Coolant System |
Threading Dial |
Leveling Bolts & Pads |
Tailstock Quill with Tang |
Inch/Metric Dials on Compound & Cross Slide (Direct Readings) |
Tool Box |
Operation Manual |
No comments yet.
Leave a comment
« BRAND NEW GEKA HYDRAULIC IRONWORKER 185 Ton BRAND NEW GEKA HYDRAULIC IRONWORKER, Mdl. HydraCrop165S, Magnetic Work Light, Rectangular Coper Notcher, Round Punch & Die Starter Set, Machined Notcher Gauging Table, 40″ Calibrated Electric Length Gauge, Machined Punch Gauging Table with X & Y Scales and Backstop, Support & Miter Table for Plate Shear, Quick Change Punch Holder, Offset Punch & Die Holder, (2) Foot Pedals, #SMHYDRACROP165S | Used Machinist Vertical Mill 10″ x 48″ Used Machinist Vertical Mill, Mdl. Dynapower, Bridgeport Table Power Feed, Drill Chuck, #A4998 »